This is a great set to have. It's the perfect combination of function over form and quality. Everything there serves a purpose and there's no unnecessary embellishments. Even so, they managed to make it look nice.. sexy even (Yeah I went there). One of the things that surprised me the most was the thought and care in the container itself. It's seamlessly smooth to select the appropriate bit, barely lifting up to release it from it's deceptively strong clasp. If you're using several bits in quick succession, you can leave them slightly raised up once removed from its clasp so it's easy to remember which ones you were using and change them out that much faster. The 'heel' if you will of the driver pivots laterally (spins) which allows you to keep your palm against it and not have to re-grip it entirely. There's a small piece of rubber along the shaft to aid in grip along with a fishnet cut-out of the shaft closer to the tip, again for grip. There's a fairly strong magnet to keep your bit in place. If you need an extra few inches, there's a little sliding cone you push up, pull your extension out, and it locks firmly in its extended position. It won't lock unless it's fully extended or retracted, so no in-between settings, but that's perfectly fine by me. The bits themselves I've been quite rough with frankly and they've taken the beating like a champ. The only bits I've noticed slight wear on so far is the smallest of the Phillips and flathead, however this I'm sure is entirely my fault as I've been using them to pry panels open shortly after removing the screws. It's a bad habit I need to stop before I damage the bits beyond hope. After you've finished your project or what-have-you, simply push in any raised bits that had been selected, close it up and be on your merry. Again I'll point out the container, flipping the top so it sits underneath was a clever space-saving idea which comes in handy for people like me with cluttered desks and shelves and lateral area is precious.. Can't afford to have half the case just being pointlessly obstructive. I understand I've been long-winded, my points wander around and I'm terrible with run-on ideas (or sentences), but this is hands-down one of my best purchases ever from Amazon.
And just because I think no review is valid unless it points out some kind of flaw or defect, the only two bad things I can say about the product is this: the sliding coupling to extend or retract the bit is a bit sharp on the edge, just a little pain, a slight nuisance, but it's a subtle aggrevation I bear silently because it's a small price to pay for this precision tool made by Hephastus himself. And when the top is flipped under, the catch or clasp for the container just sits there useless, and God forbid if your workstation gets bumped or something and the container falls, the chances of damage to the clasp and hinges is much higher than if the clasp held the container in the open position.
And one last thing this is a bit of constructive criticism I feel would be an easy and very cost-efficient way to improve the quality of future products. If, on the interior of the lid there was a thin strip of rubber or something similar so when you open the container and implement the new dual-use clasp to secure the container, there would then be some grip facing down on your work surface to keep it stable, if it needed to rest on slight angles or keep it from vibrating away.
| Brand | NANCH |
|---|---|
| Number of Items | 1 |
| Head Style | Flat Head,Phillips,Torx,Security Torx,Hex,Triangle,Tri-point,Star(Pentalobe),Spanner. |
| Material | Imported S2 Alloy Steel |
| Color | Silver |
| Recommended Uses For Product | Computers,Ring doorbell,Smartphones or Tablets,Toys,etc. |
| Special Feature | Portable, Magnetic Tip, Ergonomic Screwdriver Handle, Adjustable |
| Item Dimensions LxWxH | 5.71 x 2.56 x 1.18 inches |
| Item Weight | 268 Grams |
| Model Name | H8-S2 |
| Manufacturer | Nanch Precision Tools |
| Part Number | H8 |
| Item Weight | 9.5 ounces |
| Product Dimensions | 5.71 x 2.56 x 1.18 inches |
| Country of Origin | China |
| Item model number | H8 |
| Is Discontinued By Manufacturer | No |
| Size | Small |
| Style | Sturdy manual screwdriver set |
| Finish | Anodic Oxidation and milled knurling |
| Pattern | 22 in 1 |
| Shape | Straight |
| Item Package Quantity | 1 |
| Number Of Pieces | 23 |
| Extension Length | 20.5 Centimeters |
| Handle/Lever Placement | Push Button |
| Number of Handles | 1 |
| Handle Material | Metal |
| Blade Length | 45 Millimeters |
| Tool Tip Description | Magnatic Nut Drivers |
| Special Features | Portable, Magnetic Tip, Ergonomic Screwdriver Handle, Adjustable |
| Usage | Amateur,Professional |
| Included Components | One aluminum screwdriver handle with 22 bits,one collection case |
| Batteries Included? | No |
| Batteries Required? | No |
